Monico CDL Especificaciones descargar pdf (Pagina 30)

v1.05

6.26.09

- 30 -

59 Generator Phase A Power Factor Lead/Lag Status 30059 0=Current lags voltage, 1=Current leads voltage, 224-255

Fault Identifiers*

60 Generator Phase B Power Factor Lead/Lag Status 30060 0=Current lags voltage, 1=Current leads voltage, 224-255

Fault Identifiers*

61 Generator Phase C Power Factor Lead/Lag Status 30061 0=Current lags voltage, 1=Current leads voltage, 224-255

Fault Identifiers*

62 Generator Average Power Factor Lead/Lag Status 30062 0=Current lags voltage, 1=Current leads voltage, 224-255

Fault Identifiers*

67 EPG Circuit Breaker Status (GSP+P only) 30067 0=Breaker open, 1=Breaker closed, 228=Breaker sensor input

shorted low

151 Engine Coolant Pump Pressure Status 30151 0=coolant pressure OK, 1=coolant pressure too high, 2=Too

Low. 0-223 is Valid Range, 224-255 are Fault Identifiers

200 Hydrax Oil Pressure Switch Status 30200 22=Open, 23=Closed. 65504-65535 are Fault Identifiers

202 Emissions Feedback Mode 30202 394=Combustion Time Feedback, 395=Exhaust Temperature

Feedback, 397=Calibration Feedback, 398=No Feedback,

65504-65535 are Fault Identifiers

Multistate

Read from modbus register as unsigned integer. The value indicates different status conditions depending on

the value being read. See details below:

Monico

PID Description Modbus

Address

Manual Remarks

22 Generator Phase Select 30022 0=Phase A-B Volts A current, 1=Phase B-C Volts B current,

2=Phase C-A Volts C current

25 Generator AC Voltage Full Scale and External PT

Setpoint

30025 0=700v, 1=150v, 2=300, 3=500, 4=600, 5=750, 6=3k,

7=4.5k, 8=5.25k, 9=9k, 10=15k, 11=18k, 12=30k

26 Generator AC Current Full Scale Setpoint (Read) 30026 starting at 0:

75,100,150,200,300,400,600,800,1k,1.2k,1.5k,2k,2.5k,3k,4k

Amps

31 ECM in Control (Marine Only) 30031 0=Primary ECM is controlling, 1=Backup ECM is controlling

57 Generator AC Voltage Full Scale Transformer Setpoint 30057 0=700v, 1=150v, 2=300, 3=500, 4=600, 5=750, 6=3k,

7=4.5k, 8=5.25k, 9=9k, 10=15k, 11=18k, 12=30k

58 Generator AC Current Full Scale Setpoint 30058 starting at 0:

75,100,150,200,300,400,600,800,1k,1.2k,1.5k,2k,2.5k,3k,4k

Amps

68 Remote Generator Synchronizer Control (GSP+P only) 30068 (This can be written to) 0=Off, 1=Remote synchronization

test, 2=Automatic synchronization

69 Remote Synchronization Control Readiness (GSP+P

only)

30069 0=Not installed, 1=ready for remote command,

2=Synchronizing switch not in auto, 3=Engine control switch

not in auto, 4 Engine was not started remotely, 5 Engine not

running

70 Generator Synchronizer Control Status (GSP+P only) 30070 Starting at 0: Not installed, Inactive, Semiautomatic

paralleling, Permissive paralleling, Remote synchronization

testing, Synchronizing, Synchronization system alarm or

diag., Remote synchronization testing passed, Dead bus time

delay, Closing to dead bus.

201

ormal Stop Input Status 30201 113=Run, 174=Stop

1 2 ... 25 26 27 28 29 30 31 32 33 34 35 ... 45 46

Comentarios a estos manuales

Sin comentarios

Monico CDL Especificaciones Pagina 30

Comentarios a estos manuales